- 您现在的位置：买卖IC网 > Sheet目录891 > YS12S16-0 (Power-One)CONVERT DC/DC 88W SMD
YS12S16 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 16A
R EXT ? External resistor between TRIM pin and
voltage source; the value can be chosen depending
on the required output voltage range [k ? ].
Control voltages with R EXT ? 0 and R EXT ? 15K are
shown in Table 2.
Table 2: Control Voltage [VDC]
V 0-REG [V] V CTRL (R EXT = 0) V CTRL (R EXT = 15K)
0.7525 0.700 0.700
1.0 0.684 0.436
1.2 0.670 0.223
1.5 0.650 -0.097
1.8 0.630 -0.417
2.0 0.617 -0.631
2.5 0.584 -1.164
3.3 0.530 -2.017
5.0 0.417 -3.831
5.5 0.384 -4.364
Protection Features
Input Undervoltage Lockout
Input undervoltage lockout is standard with this
converter. The converter will shut down when the
input voltage drops below a pre-determined voltage;
it will start automatically when Vin returns to a
specified range.
The input voltage must be at least 9.6V (typically 9V)
for the converter to turn on. Once the converter has
been turned on, it will shut off when the input voltage
drops below typically 8.5V.
Output Overcurrent Protection (OCP)
The converter is protected against overcurrent and
short circuit conditions. Upon sensing an over-
current condition, the converter will enter hiccup
mode. Once over-load or short circuit condition is
removed, Vout will return to nominal value.
Overtemperature Protection (OTP)
The converter will shut down under an over-
temperature condition to protect itself from
overheating caused by operation outside the thermal
derating curves, or operation in abnormal conditions
such as system fan failure. After the converter has
cooled to a safe operating temperature, it will
automatically restart.
Safety Requirements
The converter meets North American and
International safety regulatory requirements per
UL60950 and EN60950. The maximum DC voltage
between any two pins is Vin under all operating
conditions. Therefore, the unit has ELV (extra low
voltage) output; it meets SELV requirements under
the condition that all input voltages are ELV.
The converter is not internally fused. To comply with
safety agencies requirements, a recognized fuse
with a maximum rating of 15 Amps must be used in
series with the input line.
Characterization
General Information
The converter has been characterized for many
operational aspects, to include thermal derating
(maximum load current as a function of ambient
temperature and airflow) for vertical mounting,
efficiency, start-up and shutdown parameters, output
ripple and noise, transient response to load step-
change, overload and short circuit.
The figures are numbered as Fig. x.y, where x
indicates the different output voltages, and y
associates with specific plots (y = 1 for the vertical
thermal derating, …). For example, Fig. x.1 will refer
to the vertical thermal derating for all the output
voltages in general.
The following pages contain specific plots or
waveforms associated with the converter. Additional
comments for specific data are provided below.
Test Conditions
All data presented were taken with the converter
soldered to a test board, specifically a 0.060” thick
printed wiring board (PWB) with four layers. The top
and bottom layers were not metalized. The two inner
layers, comprising two-ounce copper, were used to
provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that heat
transfer from the converter to the PWB was
minimized. This provides a worst-case but consistent
scenario for thermal derating purposes.
All measurements requiring airflow were made in the
vertical and horizontal wind tunnel facilities using
Infrared (IR) thermography and thermocouples for
thermometry.
MCD10207 Rev. 1.0, 24-Jun-10
Page 7 of 27
www.power-one.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
YV12T25-0
CONVERT DC/DC 137W T/H
ZA5350-B
CLIP TERM W/8"CORD BARE
ZA5350
CLIP TERM W/8"CORD & DC PLUG
ZCAT12V-BK
FILTER CABLE/CLAMP 140 OHM 12MM
ZCAT6819-5230D-BK
FILTER CABLE/CLAMP 35 OHM 40COND
ZL9101MIRZ-T
DCDC DGTL PMBUS MODULE 12A 21QFN
ZL9117MIRZ
IC DC/DC MODULE 17A 21QFN
ZY1015G-T3
PROGBL CONVERT DC-DC 15A OUT SMD
相关代理商/技术参数
YS12S16-0G
功能描述:DC/DC转换器 0.7525-5.5Vout 16A 9.6-14Vin RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
YS12S16-0G-Q
功能描述:DC/DC CONVERTER 0.7525-5.5V 88W 制造商:bel power solutions 系列:Y 包装:剪切带（CT） 零件状态:停产 类型:非隔离 PoL 模块 输出数:1 电压 - 输入（最小值）:9.6V 电压 - 输入（最大值）:14V 电压 - 输出 1:0.7525 ~ 5.5 V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:16A 功率（W） - 制造系列:88W 电压 - 隔离:- 应用:ITE（商业） 特性:远程开/关，OCP，OTP，UVLO 安装类型:表面贴装 封装/外壳:6-SMD 模块 大小/尺寸:1.30" 长 x 0.53" 宽 x 0.33" 高（33.0mm x 13.5mm x 8.3mm） 工作温度:-40°C ~ 85°C 效率:94.8% 功率（W） - 最大值:88W 标准包装:1
YS12S16-DG
功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
YS130101P14B
制造商:n/a 功能描述:Power SCR
YS130101P18C
制造商:n/a 功能描述:_
YS130101UHP18C
制造商:n/a 功能描述:_
YS1363
功能描述:ANT YAGI 3ELEM 150MHZ 7.1DBD AG RoHS:是 类别:RF/IF 和 RFID >> RF 天线 系列:- 标准包装:1 系列:*
YS150103AHP18C
制造商:n/a 功能描述:Power SCR